Tag: design
Landscaping a front garden
After I completed the paver installation in 2013 ( LINK ), it was time to finish the rest of the front landscaping. As always, I am not a contractor; there may be better ways to do this. Also very important, call your local utilities and have…
Building a boat motor stand
I purchased an older Evinrude 2hp boat motor (model E2RCNE), and I wanted an easy way to store and service it – the obvious solution is to build a motor stand/dolly. I started off with a ‘movers dolly’ from Princess Auto – it was made…
Man cave build-up
Man cave build-up. AKA, the garage. I will let the pictures do the talking…
Fiero engine bay
I was doing some measurements for a turbo installation. It’s been a while since I touched the engine bay, so I thought i’d post a picture of it’s current state.
Building a Shed Base – The Right Way
The grading on our property had a ditch at the north side. Unfortunately it was in the area where a planned shed was going to go. We could not alter our grading because of the municipal engineering for water drainage. So a base was required…
Installing an electrical panel plywood “backer”
The builder didn’t provide anything to mount accessories around the electrical panel. Most builders (obviously not all) give a plywood surface to mount the phone demarcation point and satellite/cable lines. Since organization makes life easier, …a plywood panel needed to be installed. This was a…
Installing a LCD screen mount with no stud anchors
If you need to install an LCD screen in an area that doesn’t have studs accessible to anchor the mount(s), then this post should help you out. There are two windows (on each side) where the LCD mount needed to be installed. The mount being…
Fiero interior is pretty much DONE
I need to install the interior door panels, …and finish installing the sound system, …but aside from those two elements, the interior is done.
Fiero custom dash is now installed!
Big day. After 7 months of hard work, the dash is finally back in. I still need to add the components – such as the extra gauges and the MP3 player. But it is satisfying to see this interior come together. FINALLY.
TRON Recognizer – NEW model
I’ve been working on this model in parallel with the other Recognizer model. I think I like this one better. I used a lot of reference pictures – especially for the textures. It still needs more work, but it’s almost there.
Fiero dash vent
I re-used the original grille for the front window vent on the PISA dash. I cut off all the mounting tabs, sandblasted the old paint off, then I put on a fresh coat of black paint to match the rest of the interior. An epoxy…
Fiero custom centre console
The upholstery on the centre console/armrest is now complete. The openings for the shifter and the window switches were created.
Fiero fiberglass headliner
I finished the upholstery on the headliner. The sunroof and overhead light outlets were covered by the headliner material from the upholstery shop. Due to the gap between the headliner and the sunroof, I used foam tape to fill in the seam.
Fiero interior pieces are back from upholstery
The interior pieces came back from upholstery, and all I can say is WOW. I can’t wait to get these installed! The pictures don’t do them justice.
Fiero alarm system wiring is done + more painting
I have completed the wiring of the alarm system. With all the black wire-loom, it looks like something from a sci-fi movie. I have also started painting the dash support pieces to match the rest of the interior trim.
Fiero alarm siren and custom LED switches
Today I finished mounting the alarm system siren. I used an aluminum bracket to attach it to the chassis. I also mounted three custom LED switches (purchased last year) to the interior power window plate. I will run the fog lights to one of the…
Installation of the Fiero electrical junction box
I have completed the installation of the custom junction box to the Fiero chassis. This will allow easy electrical hookup for the aftermarket accessories.
Prepping the Fiero dash for upholstery
I’m just finishing off a few outstanding items: – Completion of the glove box with magnets. – Addition of a multi-switch plate inside the glove box – I will wire additional lighting (for car shows) to these switches in the future. – Completed the speaker…
Revisit the Fiero glove box
The Velcro option was not working well. So I came up with another solution – MAGNETS. I used epoxy to glue a 9″ piece of metal to the glove box door, and I secured 4 magnets to the internal adjuster plate.
Fiero HVAC system is complete
I have completed the installation of the HVAC system. The 2.5″ SHOP-VAC tubing was used to run the air-flow, and a plate (made of fiberglass) was fabricated – this allowed the tubes to mount to the stock HVAC outlet. This was a time consuming modification…
Fiero ducts are mounted
The ducts were secured to the fiberglass dash using something called a Chicago nut/bolt fastener – they are also called barrel nuts/bolts. They have a very low profile, so it won’t interfere with the upholstery or the trim pieces. The couplers I glassed in are…
Fiero PISA dash glove box install
It took a while for me to think about how I was going to mount the glove box door. I found a set of 1″ brass hinges (at Canadian Tire) that were small enough to be hidden, …but big enough to provide support strength. The…
Solution for custom Fiero HVAC
I’ve decided against the installation the stock HVAC system – it was causing fitment issues with the PISA dash. So I’m going to run a custom venting system using vacuum tubing. More details to follow….
Fabrication of custom bracket for Fiero junction box
Since I am installing the PISA Fiero dash, I have some room to add an electrical junction box. This junction box will act as a future expansion for interior electronics. I used an existing bracket I pulled from the Fiero and welded it onto another…
